VW Touran 2005 Steering Fault

September 30, 2019, 6:57 am

≫ Next: Skoda Octavia II 2013 CAYC No Crank

≪ Previous: Audi A4 B8 2013 Sedan Tail LED Lamps USA To EU Conversion

$

0

0

Car comes with these errors:

Address 44: Steering Assist Labels: 1Kx-909-144-G2V2.clb
Control Module Part Number: 1K1 909 144 H
Component and/or Version: EPS_ZFLS Kl.6 1502
Software Coding:
Work Shop Code: WSC 00000 000 00000
VCID: B02C562D23BF30CFA9-80E4

1 Fault Found:

00003 - Control Module
014 - Defective - MIL ON

And in MWB 2 Relaisvoltage 8.6V, in MWB 9 the steering curve is 69.
I look for voltage on connectors and all is OK.
Now i flashed a new software with this file LH0041504 and for steering curve this one V074M0691K0___Lenkung.

But now i have this errors and in MWB 9 there is 0:

Address 44: Steering Assist Labels: 1Kx-909-144-G2V2.clb
Control Module Part Number: 1K1 909 144 H
Component and/or Version: EPS_ZFLS Kl.6 1504
Software Coding:
Work Shop Code: WSC 00000 000 00000
VCID: B02C562D23BF30CFA9-80E4

3 Faults Found:

00003 - Control Module
014 - Defective - MIL ON
00003 - Control Module
005 - No or Incorrect Basic Setting / Adaptation
02870 - Function Restricted due to Faulty Data
008 - Implausible Signal - MIL ON
Freeze Frame:
Mileage: 2280 km
Temperature: 22.0°C
Voltage: 7.80 V
Voltage: 13.10 V

Someone know if i have flashed the right steering curve?
Also Here a TPI that this error should disappear with an update.
Thanks.

link.txt
File Type:
Downloaded:	0 times
Size:	359 bytes

---

Skoda Octavia II 2013 CAYC No Crank

September 30, 2019, 8:24 am

≫ Next: Toyota Yaris 2009 Stop/Start System Malfunction

≪ Previous: VW Touran 2005 Steering Fault

$

0

0

Hi all,
I have an Octavia II with CAYC engine and NTT (DSG) transmission that will not crank.
There are no fault codes.
If I power the J682 relay (starter relay terminal 50) the engine cranks but doesn't start.
P/N test in transmission is OK.
If I run the J519 (central electrics module) terminal 50 test in GFF I only get two of the values to change to ON.
The CAN out Terminal 50 always reads off.
Terminal 75 test does the same.
Terminal 15 and 30 both test correct.
Any ideas welcome.
Thanks.

IMG_20190930_121111.jpg.pdf
File Type:
Downloaded:	4 times
Size:	4.49 MB

Toyota Yaris 2009 Stop/Start System Malfunction

September 30, 2019, 9:40 am

≫ Next: Mitsubshi 2018 Eclipse Cross Key Registration Manual

≪ Previous: Skoda Octavia II 2013 CAYC No Crank

$

0

0

Got this Yaris in with stop/star not working, diagnosed it and found there is NO communication with the stop/start module.
Check basic fuses in engine bay fuse box and all fuses looked ok...
It would be nice if somebody could help me with the wiring diagram and the location for the stop/start module.
Would be a great help...
Here is the VIN for above vehicle VNKKH98310A062626, also if there are any common things to look at it please?

Mitsubshi 2018 Eclipse Cross Key Registration Manual

October 1, 2019, 12:13 pm

≫ Next: Land Rover P38

≪ Previous: Toyota Yaris 2009 Stop/Start System Malfunction

$

0

0

Eclipse Cross Key Registration Manual.

Scan 26 Sep 2019 at 4_58 PM.rar
File Type:
Downloaded:	2 times
Size:	2.27 MB

Land Rover P38

October 2, 2019, 2:15 am

≫ Next: [Request] Hyundai Santa Fe 2001 2.0 CRDi Wiring Diagram

≪ Previous: Mitsubshi 2018 Eclipse Cross Key Registration Manual

$

0

0

Hello,
Someone can tell me what interface work on Land Rover P38/1999/2.5 TD ?
KTS and Launch not work on ABS
Thank you

[Request] Hyundai Santa Fe 2001 2.0 CRDi Wiring Diagram

October 2, 2019, 10:47 am

≫ Next: VW Passat 3C 2008 Comfort Module Virgin Dump

≪ Previous: Land Rover P38

$

0

0

Hello everyone.
I need the electrical scheme of a 2001 Hyundai Santa Fe with 2.0 CRDI engine (type D4EA).
I have two fault codes referring to the CAN line, but all the scheme programs I have show me a scheme in which no line appears CAN Bus.
If anyone can help me I appreciate it.

VW Passat 3C 2008 Comfort Module Virgin Dump

October 2, 2019, 11:00 am

≫ Next: BMW ETK 10.2019

≪ Previous: [Request] Hyundai Santa Fe 2001 2.0 CRDi Wiring Diagram

$

0

0

Hello all.
Can anybody share virgin dump file from eeprom 95320 of comfort module 3C0959433AB?
I can share virgin from 433AR and 433M.
Thank you.

BMW ETK 10.2019

October 2, 2019, 3:48 pm

≫ Next: Mitsubishi Grandis 2006 2.0 Starting Issues

≪ Previous: VW Passat 3C 2008 Comfort Module Virgin Dump

$

0

0

Hello to all AP Members...

Well in sort, here it is the LATEST BMW ETK 10.2019 (The Spare Parts for BMW Group Cars & her Motorcycles)...



As always, BMW ETK = Multilanguage!

Enjoooooooooooooy ppl!

Best Regards!

BMW ETK 10.2019 (Mega).txt
File Type:
Downloaded:	0 times
Size:	181 bytes

---

Mitsubishi Grandis 2006 2.0 Starting Issues

October 3, 2019, 10:13 am

≫ Next: I Need PIN Code For Peugeot 307

≪ Previous: BMW ETK 10.2019

$

0

0

Evening.

I need engine ECU wiring diagram or ECU control relay wiring diagram.
The problem is that the car starts sometimes.
When it does not start there is no ground to the engine control relay Pin 85 and there is no communication with engine ECU, Immo, ETACS and so on.

I have replaced the engine ECU (edc16u31) but no joy.
I do not know from where the control ground to the relay come from.
I suspect ETACS module but I'm not sure.
Engine code: BSY

Please help!

BR

I Need PIN Code For Peugeot 307

October 4, 2019, 2:55 am

≫ Next: Vauxhall Vivaro 2016 1.6D Speed Limiter Remove

≪ Previous: Mitsubishi Grandis 2006 2.0 Starting Issues

$

0

0

I Need PIN Code For Peugeot 307

VIN: VF33E8HZB8251001

TKANKS

Vauxhall Vivaro 2016 1.6D Speed Limiter Remove

October 4, 2019, 11:55 am

≫ Next: Lexus LS 430 Lambda Disconnecting Issue

≪ Previous: I Need PIN Code For Peugeot 307

$

0

0

I would like to remove the speed limiter on this Van using dealer tool before I use my CMD BDM.
What is the procedure to do this task?
See attachment for vehicle details.

vivaro speed limiter.pdf
File Type:
Downloaded:	2 times
Size:	84.69 KB

Lexus LS 430 Lambda Disconnecting Issue

October 5, 2019, 8:59 am

≫ Next: VAG Lane Change Camera (A5) Gateway Flashing Issue

≪ Previous: Vauxhall Vivaro 2016 1.6D Speed Limiter Remove

$

0

0

Hello guys.
I have problem with Lexus LS 430.
The case is i have blown 7,5 ECU2 fuse and on this fuse there is MAF, Lambdas, and vacuum valve.
I have problem witch disconnecting rear lambdas. Do i need to remome carpet inside car?
Maybe anyone did it and can help?

VAG Lane Change Camera (A5) Gateway Flashing Issue

October 5, 2019, 9:40 pm

≫ Next: Key programming all key lost

≪ Previous: Lexus LS 430 Lambda Disconnecting Issue

$

0

0

7N0907530AJ Gateway - Can it be flashed to 7N0907530AN with fatigue Detect?

Hi I'm trying to find out if I can flash a 7N0907530AJ Gateway over to 7N0907730AN and with the fatigue detection. I had to write the fatigue code to the AJ EEPROM the last time manually to get the fatigue detection option to work.

I'm trying to get the newer 3AA-980-654-D Lane Change Camera (A5) to work, and I don't think it likes the gateway as I can't get it to communicate in Vagcom to save my life.... I've tried 2 different cameras so far and neither of them allow me to communicate with them. Wondering if I can try flashing that gateway to the "AN" version to see if that does anything.

Does anyone know?

Key programming all key lost

October 6, 2019, 7:36 pm

≫ Next: Audi TT 2005 Immo OFF

≪ Previous: VAG Lane Change Camera (A5) Gateway Flashing Issue

$

0

0

Hello I need help in getting a pwf file to program keys, to a 2018 Mitsubishi smart key system. Please pm if you can.

Audi TT 2005 Immo OFF

October 7, 2019, 7:14 am

≫ Next: [Request] Hyundai i20 2009 1.3 Workshop Manual

≪ Previous: Key programming all key lost

$

0

0

Hi peeps.
I've just done a immo off on a 2005 TT because the old clocks failed.
The car wouldn't start and the clocks couldn't be repaired due to parts availability.
So I decided to get some used clocks and go for the immo off option.
Carried out an immo off using Immo Universal 3.2 and the car is running but I have the safe message on the radio and a flashing immo key light on dash
The ECU was a MED 7.5 and the eeprom was a 95040.
Can someone rectify my original dump or upload a good one please?
ECU is Bosch ME 7.5 8N0 906 018 CS and VIN of the car: TRUZZZ8N361005445

audi tt.zip
File Type:
Downloaded:	1 times
Size:	450 bytes

---

[Request] Hyundai i20 2009 1.3 Workshop Manual

October 8, 2019, 11:54 am

≫ Next: [Request] Java Runtime 6.26 [SOLVED!]

≪ Previous: Audi TT 2005 Immo OFF

$

0

0

Hello guys.
I need a workshop manual for Hyundai i20 1248cc year 2009, engine type G4LA 57,2KW.
Thanks in advance.

[Request] Java Runtime 6.26 [SOLVED!]

October 8, 2019, 12:20 pm

≫ Next: BMW CAS 2 Eeprom Error

≪ Previous: [Request] Hyundai i20 2009 1.3 Workshop Manual

$

0

0

Thank you.

BMW CAS 2 Eeprom Error

October 8, 2019, 12:37 pm

≫ Next: 2018 Honda Acord Spo- BCM replace - help

≪ Previous: [Request] Java Runtime 6.26 [SOLVED!]

$

0

0

Please help repair corrupted CAS 2 eeprom 2K79X. Error A0AD EEPROM_Writing_error.

2K79X_eeprom.rar
File Type:
Downloaded:	0 times
Size:	1.2 KB

2018 Honda Acord Spo- BCM replace - help

October 9, 2019, 2:58 pm

≫ Next: VW Golf MK7 2 Door Coding

≪ Previous: BMW CAS 2 Eeprom Error

$

0

0

Am changing BCM on 2018 Honda Accord Spo, could someone give a guide with mvci or which other tool

VW Golf MK7 2 Door Coding

October 9, 2019, 5:55 pm

≫ Next: BMW E61 2.0D Steering Lock Issue

≪ Previous: 2018 Honda Acord Spo- BCM replace - help

$

0

0

Hi,

I bricked a vw golf mk7 cluster and I changed a used cluster. I did not save the original coding and now I have problem with the doors light. Anyone know how to code this cluster from 4 doors to 2 doors?

Regards,